remove shower drain grate

Use a Phillips screwdriver to remove each screw around the grate. Gave it a tap with hammer and screwdriver but no movement.

How To Remove A Shower Drain Cover In 5 Minutes Plumbing Sniper

Put masking tape around the drain prior to cutting the caulking.

. If your Shower drain is clogged you will need to remove the cover to clean out the hairI. A bleach solution is very effective against mold. Set the grate back in place then fill the gaps with grout but dont let the grout run over the radius edge of the grate otherwise youll lock it back in place.

Most if not all floor grates in 60s were fixed. I assumed it was threaded and screwed into an iron pipe as there is no obvious screws etc. Using the palm of your hand apply pressure on the uppermost end of the screwdrivers handle.

Place the screws in a resealable bag or tray so they dont get lost or fall down the open drain. Then use your other hand to rotate it until the screw comes out. You woould bend the end of the wire about 2 from the end to a point.

Youll need Phillips screwdriver to loosen screws holding the screw-in shower drain in place. Gently pry it up and you can scrub the inside of the drain with a cleaner of your choice. Tub Drain Remover Wrench - Use to Install and Remove Most Bath and Shower Drains and Closet Spuds Square Plastic Toilet Seat Nuts.

It looks like the perimeter of the drain should be grouted but that is really a shell that the drain grid fits into. To move it I would normally put something down vertically in the outer slot and hit it from side on but I like Alexs idea. 18 inch - Drain Hair Clog Remover Tool with Rotating Handle 5 Wand Refills - Thin Flexible Easy to Use on Most Drains Grates - Made in USA 5-Pack 43 out of 5 stars 21268.

44 out of 5 stars 224. The retaining nut and washer drop down staying below the shower pan. Youll find a variety of shower drains on the market.

Try to clean out around the edge of the grate as much as possible and a bit of tapping around the outer rim may help loosen things up too and as Alex says a bit of WD40. Whatever you can put a bend on that you can insert into the grate and then basically hook the strainer. Remove the washcloth and set it to the side.

I dont want to be too rough though. He should have not grouted that inner perimeter. You can get a 18 length of wire.

The tape should prevent the grout from adhering to the grate. Probably has some soap scum and calcification holding it. I would guess it is a one piece and not a removable grate.

The Oatey 42150 is the most common model for fiberglass acrylic and other preformed shower bases and it comes in. Loop a piece of string through the drain holes in the grate. Place the tip of the screwdriver in one of the grates and use it to pop up and lift the drain cover.

You can try turning it but screw-on covers generally dont have screws. 1 Remove the grate by cutting around the grout with a utility knife or trying to pry the outer edges with a screwdriver and digging into the grout 2 Clean drain with a snakeplunger. How to remove a shower drain cover cap that doesnt have screws.

That type of drain cover is usually held in place with only the two screws. Insert the point into the strainer then lift it so that the short end comes up a second opening. How to Remove a Screw-in Shower Drain Cover A Step-By-Step Guide.

For example the Oatey 42045 shower drain illustrated by funbro1 on YouTube consists of a plastic housing that you glue onto the waste pipe and a plastic strainer assembly that you screw into it. See how grout in 7 eye-catching colors is spicing up kitchens and bathrooms abroad.

How To Remove This Shower Drain Grate Or Otherwise Remove Mold From The Pipe Underneath Home Improvement Stack Exchange